Results Per Page | Showing 1-25 of 25 Results
| 1
Answer:
In addition to the instructions provided, the following may be helpful:
...
View Answer
Answer:
Important: Only GEN3 Gateways are eligible for conversion to MVP Access. The uniVerse Finder Utility Software must be installed on the same local area network as the gateway.
...
View Answer
Answer:
To use the AUX relay of a Trilogy Networx™ System NETWORXPANEL Wireless Networx Control Panel that is connected to an Air Access system, configure the Shunt Relay option as follows:
...
View Answer
Answer:
Your DL-Windows software version is outdated. If you have discovered a lock without a model number listed (see example image, below), it is likely that your DL-Windows software is older than the model itself.
...
View Answer
Answer:
With the release of DL-Windows V5.5.3, we have added a Two-Door Settings tab in the Features screen that includes the ability to activate Passage Mode in either the main relay or the auxiliary relay, or both relays together. Note: This new Two-Door...
View Answer
Answer:
The ArchiTech series N90 (cylindrical) N95 (mortise) support the iLock Bluetooth app. The model number must contain the letter J (N90J or N95J) or T (N90T or N95T) to indicate that the Bluetooth option is present.
...
View Answer
Answer:
No, an RR-RECEIVER is not necessary to pair the RR-1BUTTON to a NETWORXPANEL because the NETWORXPANEL already has a receiver built into it. To pair the RR-1BUTTON to a NETWORXPANEL, a NETDK or NETPDK locking device must be wired to the system,...
View Answer
Answer:
When programming the RR-1BUTTON to be used with a NETWORXPANEL, the main ("primary") relay always activates first, usually bypassing the auxiliary relay unless otherwise programmed to do so.
...
View Answer
Answer:
After the lock has been physically defaulted, proceed as follows:
...
View Answer
Answer:
As the NETHIDNSPANEL does not include a keypad, it is not possible to perform keypad Function 65 (normally used to pair the RR-1BUTTON to a Networx lockset or NETWORXPANEL). However, you can purchase the RR-TRILOGYKIT which includes a small...
View Answer
Answer:
Whether the NETWORXPANEL is wired with one or two keypads or is configured for a single door or for "Two Door Mode", the pairing of a wireless remote release button to the NETWORXPANEL is the same. If the NETWORXPANEL is wired with two keypads,...
View Answer
Answer:
When in "Two Door Mode", the shunting of the Remote Release Input terminals 26 and 27 (or the activation of a paired wireless remote release button) will always activate BOTH relays, unlocking both doors at the same time.
View Answer
Answer:
Up to 10 wireless remote release buttons can be paired to the NETWORXPANEL.
...
View Answer
Answer:
The pictures shown below represent two views of an actual AL-IMEPOEP, with color coded lines and numbers indicating the various dimensions (in inches).
View Answer
Answer:
As with most upgrades, the potential for data loss always exists. We therefore strongly recommend that prior to upgrading your Lenel OnGuard software, you always back up the following configuration file:
...
View Answer
Answer:
The dimensions are (WxHxD) 7 x 3½ x 1½" (17.8 x 8.9 x 3.8cm)
View Answer
Answer:
Other than checking the batteries for adequate voltage, remove the lock from the door and inspect the ribbon cable for damage. A damaged ribbon often causes a short on the battery connections, drastically decreasing battery life.
View Answer
Answer:
The versatility of the Alarm Lock Networx system allows the Gateways and wireless locks to communicate over many different types of networks. For this reason, it is always a good idea to “bench test” the equipment in a controlled...
View Answer
Answer:
Leave this selection blank, as the Gateway will automatically select an available channel.
View Answer
Answer:
Two Door Mode Can Limit User Access:
...
View Answer
Answer:
DL-Windows software allows you to connect your PC with your lock. Although DL-Windows cannot make your lock a wireless lock; however, the following locksets have wireless capability:
...
View Answer
Answer:
There is no specified length of the RJ-45 cable between two devices. However, we recommend you consider the following variables:
...
View Answer
Answer:
To move Existing Networx Account Files to a New Computer, follow the steps below:A. COPY Your EXISTING ACCOUNT FILES
...
View Answer
40 Results Per Page | Showing 1-25 of 25 Results
| 1
