Results Per Page | Showing 1-39 of 39 Results
| 1
Answer:
To test the programming of an existing Test Timer feature:
...
View Answer
Answer:
Yes, a zone can share two or more Areas (within the maximum number of Areas available consistent with the control panel model).
...
View Answer
Answer:
If you disconnect one or both battery leads inside a Gemini or Magnum Alert MA3000 control panel, the low battery indication may take up to 4 hours to annunciate at the keypad. This delay is because the control panel may require up to 4 hours...
View Answer
Answer:
Some older (version 9, 10, 11) Gemini control panels, including the GEM-P1632, GEM-P1664, PCD-Windows Quickloader to display an error on zone 9 when using Zone Doubling. The solution is to disable the Error Check utility, as follows:
...
View Answer
Answer:
No, the EPROM chip does NOT contain the control panel programming selections that were made in PCD-Windows Quickloader software, nor does it contain any keypad programming selections. The EPROM only contains the firmware for that control panel...
View Answer
Answer:
The GEM-P816, GEM-P1632, and GEM-P1664 control panels cannot be auto-disarmed, but the following instructions describe how to use PCD-Windows Quickloader software to enable the Auto-Arm feature at a specified time of the day on specific days of the...
View Answer
Answer:
Auto Disarming is not available with the GEM-P1632, GEM-P816 or GEM-P1664 control panels, however this scheduling feature is available with the GEM-P3200, GEM-P9600 and GEM-X255 control panels.
...
View Answer
Answer:
If you wish to use the iBridge IBR-ZREMOTE module, other iBridge system components or a StarLink Connect Communicator with an older GEM-P816 or GEM-P1632 control panel running firmware version 10D, this older control panel firmware must be upgraded...
View Answer
Answer:
If you wish to use the iBridge IBR-ZREMOTE module, other iBridge system components or a StarLink Connect Communicator with an older GEM-P816 or GEM-P1632 control panel running firmware version 10D, this older control panel firmware must be upgraded...
View Answer
Answer:
If you wish to use the iBridge IBR-ZREMOTE module, other iBridge system components or a StarLink Connect Communicator with an older GEM-P816 or GEM-P1632 control panel running firmware version 10D, this older control panel firmware must be upgraded...
View Answer
Answer:
No, with the GEM-P400, GEM-P800, GEM-P801, XP-400 or XP-600 control panels, the GEM-WP Panic Transmitter cannot be programmed to a zone; the GEM-WP must be programmed as a keyfob.
...
View Answer
Answer:
A control panel "cold start" resets the control panel back to the state it was in when it left the factory, clearing all programming and settings. ALWAYS cold start the control panel after replacing the EPROM (see WI2052).
...
View Answer
Answer:
Yes, however the control panel will only see 16 points because these older versions did not support 32-point receivers.
View Answer
Answer:
When "Panel Access" is enabled, pressing the Access Code on the keypad energizes the control panel PGM2 Output for a specified duration. Program PCD-Windows Quickloader as follows:
...
View Answer
Answer:
Yes. Use a multimeter to confirm the following readings:
...
View Answer
Answer:
Replace the prom chip as follows:
...
View Answer
Answer:
Used when the SLE-GSM radio is mounted more than 6 feet from the control panel, the SLE-DLEXT is connected between the control panel and the SLE-GSM and provides the means to remotely communicate (download/upload program and status) through the...
View Answer
Answer:
NN = Device of zone number. Note: "E" messages not listed here are currently undefined and reserved for future use.
...
View Answer
Answer:
With the Gemini control panel models GEM-P816, GEM-P1632, GEM-P1664, GEM-P3200, GEM-P9600 or GEM-X255 and the GEM-RP1 series or GEM-K1 series two-line LCD keypads:
...
View Answer
Answer:
All GEM-X255 control panels can be upgraded to the latest firmware.
...
View Answer
Answer:
For control panels GEM-P816, GEM-P1632 and GEM-P1664 firmware version 30 or higher, any keypad in the system can be used for keypad programming. For older control panel versions below V30, the programming keypad must be designated as "keypad...
View Answer
Answer:
Wire the power to the devices to the auxiliary power supply’s DC positive and negative. Then install a wire between the auxiliary power supply DC negative and panel common (either terminal 6 or terminal 10 will work with the GEM-P816,...
View Answer
Answer:
Yes. Note that Quickloader only allows the conversion to a "larger" model control panel (i.e. you may convert a GEM-P816 control panel to a "larger" GEM-P1632, but cannot convert a GEM-P1632 to a "smaller" GEM-P816. At this time, a...
View Answer
Answer:
The Napco control panels that support Zone Doubling are the Gemini GEM-P1632, GEM-P1664, GEM-P800 and the Napco Express XP-600 and XP-400.
View Answer
Answer:
The ONLY solution is to possess a working Dealer or Master Security Code to allow entry into Dealer Program Mode. This Code will allow you to make all needed changes to the control panel programming.
View Answer
Answer:
If the Master Security Code of the GEM-P1632, GEM-P1664, or GEM-P816 is not known, it will NOT be possible to re-program the control panel. It is not possible to reset the Master Security Code. Therefore, it is extremely important that...
View Answer
Answer:
If the Test Timer feature is programmed, an automatic test report will be transmitted to the central station on the scheduled day(s) at the scheduled time (UL installations require a report at least every 24 hours).
...
View Answer
Answer:
Yes. You can still use your old keypads and they will function normally, but you will not be able to access User Programming Mode nor Dealer Programming Mode.
View Answer
Answer:
When adding EZM's by means of keypad programming (in either User Mode or Dealer Mode), an EZM trouble (E12-01 through 07) may appear at the keypad after exiting programming mode.
...
View Answer
Answer:
For control panels GEM-P3200, GEM-P9600, GEM-X255:
...
View Answer
Answer:
Be aware that only one RB3008 Relay Board can be supported by each GEM-P1632 control panel.
Therefore, if two RB3008 Relay Boards are wired to a single GEM-P1632 control panel, the second RB3008 will be inoperative.
View Answer
Answer:
There is an easy way to program our new control panels for local downloading only. In firmware versions that support the NL-MOD (a device allowing the reporting of alarms over a TCP/IP-based Intranet or Internet network), we added a Central...
View Answer
Answer:
Yes, the iRemote-MOD is fully compatible with the Gemini control panels listed below if using its remote "virtual" keypad capability only. This includes User and Dealer programming (except for control panel version 9A in the GEM-P816 &...
View Answer
Answer:
Yes, the Napco GEM-K1VPS keypad is compatible with the GEM-P816, GEM-P1632 and GEM-P1664 control panels.
...
View Answer
Answer:
By default, the system trouble audible indication at the keypad will sound for 10 minutes, or until the user presses the Reset key. However, there is an option to eliminate the system trouble audible at the keypad in cases where pets or others...
View Answer
40 Results Per Page | Showing 1-39 of 39 Results
| 1
