Results Per Page | Showing
1-40 of 92 Results
| 1 |
2
|
3
Answer:
With the GEM-P3200, GEM-P9600 and GEM-X255 control panels, program a Test Timer as follows:
...
View Answer
Answer:
Unlike other communication methods, communicating using a POTS ("Plain old telephone service") requires that you first establish a connection between the Quickloader software and the control panel before all transfer operations are enabled and...
View Answer
Answer:
Some older (version 9, 10, 11) Gemini control panels, including the GEM-P1632, GEM-P1664, PCD-Windows Quickloader to display an error on zone 9 when using Zone Doubling. The solution is to disable the Error Check utility, as follows:
...
View Answer
Answer:
More than likely your Quickloader software contains outdated zone descriptions. This can happen when zones are added, removed, or changed during a service call.
...
View Answer
Answer:
Yes. To change the default communication type:
Select File > Preferences.
Select Panel Configurations. In the Default Transfer Option area, use the pull-down menus to set your preferred default communication type.
View Answer
Answer:
Yes, if you need a zone delay before reporting, add a delay using the Zone Configuration screen in PCD-Windows Quickloader software:
...
View Answer
Answer:
The control panel must be in 'normal' mode (panel configuration jumper set to NORMAL) for PCD-Windows Quickloader software to connect to the control panel. Only during Direct Access Keypad Programming (where data is entered at the keypad by address...
View Answer
Answer:
Yes, if you need a zone to delay before reporting, add a delay using the Zone Configuration screen in PCD-Windows Quickloader software.
...
View Answer
Answer:
Refer to the GEMC-RM3008 Relay Module installation instructions (WI1706) and perform the following:
...
View Answer
Answer:
An E97 trouble is an SLC trouble that can be caused by many things. To determine the exact trouble condition, launch PCD-Windows Quickloader and examine the status of the system. In the Status / Control screen, open the SLC tab. The devices in...
View Answer
Answer:
All communicators with commercial service plans are required to send a shutdown report to the central station (E308) before the firmware download. Commercial service plans have an SLB prefix and include a 200-second supervisory check-in. To allow...
View Answer
Answer:
In the PCD-Windows Quickloader Keypad Assignment screen, the selection, Remote Access Only should be disabled (unchecked). This message appears if this feature is enabled.
View Answer
Answer:
No, however if you wish to program the control panel using the FireLink Cloud Portal (www.FireLinkPro.com), the FireLink control panel must be "new, out of the box" or must be reset back to its original factory default settings and then initially...
View Answer
Answer:
Yes! Below is a video that describes how to create custom zone types in PCD-Windows Quickloader:
View Answer
Answer:
Yes, this video describes some shortcuts available in the PCD-Windows Quickloader Feature View screen:
View Answer
Answer:
Using PCD-Windows Quickloader to link multiple elevator recall outputs to the Gemini C-Series (GEMC) fire control panel:
View Answer
Answer:
Log into PCD-Windows Quickloader, click on File > Dealer Settings > StarLink Defaults tab. In the StarLink Authentication area, type your company's master StarLink Dealer ID and Password. Note: StarLink user accounts cannot be used.
...
View Answer
Answer:
PC Preset is a utility that provides the installer the ability to perform automated remote operations on several accounts. Typical uses of PC-PRESET include overnight uploading and printing of control panel logs, uploading multiple new...
View Answer
Answer:
We recommend using the latest version of Quickloader (currently V6.4.5) (for versions 6.4.2 and prior, scroll down).
...
View Answer
Answer:
Use PCD-Windows Quickloader software, available for download at the NAPCO Technical Library (https://tech.napcosecurity.com/).
...
View Answer
Answer:
1. Download the default file to your desktop.
...
View Answer
Answer:
No, the iSecure Go-Anywhere Hub should only be programmed using the iSecure Cloud Web Portal at www.iSecureByNapco.com, from either your smart device or web browser. Alternatively, you can log in to the StarLink Radio Management Center at...
View Answer
Answer:
WARNING! This procedure will delete your existing Accounts!
View Answer
Answer:
How to download the installation files from the NAPCO Technical Library (tech.napcosecurity.com) and install PCD-Windows Quickloader for the first time:
Additional information:
NAPCO PCD-Windows Quickloader Software Downloads
View Answer
Answer:
How to use PCD-Windows Quickloader to change the FireLink control panel default program.
...
View Answer
Answer:
This video shows you how to update the IP Address from the DNS Server:
View Answer
Answer:
Access the file from the NAPCO Tech Library in this link and download the file to your desktop. Log into PCD-Windows Quickloader as the Master, click File > Import Multiple Accounts..., locate the file on your desktop, select the file and...
View Answer
Answer:
The FireLink control panel has a pre-loaded Easy Default Program intended for sprinkler supervisory or basic conventional fire applications. For applications outside the scope of the default program, the FireLink system may be programmed Over-The-Air...
View Answer
40 Results Per Page | Showing
1-40 of 92 Results
| 1 |
2
|
3
