Answer:
1. Address the RM3008 according to the address chart:
...
View Answer
Answer:
To test the programming of an existing Test Timer feature:
...
View Answer
Answer:
With Zone ANDing, up to 8 groups of at least two zones each can be "AND"ed, wherein the system will go into alarm only if any two zones of the group are tripped within 2 minutes. Zone ANDing is designed to afford redundant protection for...
View Answer
Answer:
Yes, a zone can share two or more Areas (within the maximum number of Areas available consistent with the control panel model).
...
View Answer
Answer:
If you disconnect one or both battery leads inside a Gemini or Magnum Alert MA3000 control panel, the low battery indication may take up to 4 hours to annunciate at the keypad. This delay is because the control panel may require up to 4 hours...
View Answer
Answer:
Auto Disarming is not available with the GEM-P1632, GEM-P816 or GEM-P1664 control panels, however this scheduling feature is available with the GEM-P3200, GEM-P9600 and GEM-X255 control panels.
...
View Answer
Answer:
To ensure that the access control history is logged for all ACM devices within the system, program 1 active or 1 spare zone to each Area that has an ACM assigned. Having a zone assigned to an Area allows the control panel to recognize each part of...
View Answer
Answer:
This video only applies to the Gemini GEM-P9600 and GEM-X255 control panels, and must not be used for Commercial installations (Residential only).
View Answer
Answer:
No, with the GEM-P400, GEM-P800, GEM-P801, XP-400 or XP-600 control panels, the GEM-WP Panic Transmitter cannot be programmed to a zone; the GEM-WP must be programmed as a keyfob.
...
View Answer
Answer:
A control panel "cold start" resets the control panel back to the state it was in when it left the factory, clearing all programming and settings. ALWAYS cold start the control panel after replacing the EPROM (see WI2052).
...
View Answer
Answer:
The GEM-ACM1D is an accessory that adds access control functionality to the above listed control panels. The GEM-ACM1D provides controlled access to a door by releasing a magnetic lock or electric strike when a valid Prox Card is presented to a...
View Answer
Answer:
When a fire alarm occurs within a premises that has a powered front entry gate, it is important for the gate to open upon a fire alarm condition to permit entry to the fire response team. Detailed below are the steps for wiring 2-wire and 4-wire...
View Answer
Answer:
If Opening / Closing Signals are programmed, a signal is transmitted to the central station whenever the control panel is either armed or disarmed.
...
View Answer
Answer:
With "Auto Arming" enabled, the siren will always sound upon arming. If you wish to suppress the sounder, launch PCD-Windows Quickloader and re-program each zone for "AUX OUTPUT" and disable each zone for "BURGLARY OUTPUT". Wire the siren...
View Answer
Answer:
The Global Bypass option is only available with the Gemini GEM-P3200, GEM-P9600 and GEM-X255 control panels. To bypass an open zone, the standard "selective bypass" procedure is used at a system keypad. As Control4 does not have this...
View Answer
Answer:
The GEM-CO-MOD Carbon Monoxide detector requires an output to trip the carbon monoxide (CO) zone. The diagram below illustrates the correct connections from the positive CO zone (labeled COZ+) to a PGM terminal located on the GEM-P816,...
View Answer
Answer:
1. Visit the Napco Technical Library (http://tech.napcosecurity.com/) and download the latest .hex firmware file for the control panel to be updated.
...
View Answer
Answer:
Yes. Use a multimeter to confirm the following readings:
...
View Answer
Answer:
Replace the prom chip as follows:
...
View Answer
Answer:
NN = Device of zone number. Note: "E" messages not listed here are currently undefined and reserved for future use.
...
View Answer
Answer:
To upload or connect to a Gemini GEM-P3200, GEM-P9600 or GEM-X255 control panel with PCD-Manager software, you must first program the "Master Security Code" into the PCD-Manager's control panel account. To maintain the security of the control...
View Answer
Answer:
With the Gemini control panel models GEM-P816, GEM-P1632, GEM-P1664, GEM-P3200, GEM-P9600 or GEM-X255 and the GEM-RP1 series or GEM-K1 series two-line LCD keypads:
...
View Answer
Answer:
To supervise the TCP/IP connection between a GEM-P3200, GEM-P9600 or GEM-X255 control panel and a Net.Link NL-MOD communications module, enable the features "TCP/IP Communications" and "Handshake Local Telemetry" in the PCD-Windows Quickloader...
View Answer
Answer:
All GEM-X255 control panels can be upgraded to the latest firmware.
...
View Answer
Answer:
The Gemini GEM-P3200, GEM-P9600 and GEM-X255 control panels running firmware version V70 and above have a prom chip that can be flashed for firmware upgrades (instead of a chip change). The existing control panel version can be verified by...
View Answer
Answer:
With control panels GEM-P3200, GEM-P9600 and GEM-X255, wire the device power to the auxiliary power supply DC positive and negative. Then install a wire between the auxiliary power supply DC negative and control panel common (either terminal 10...
View Answer
Answer:
This Tip will work only when all zones in the system are in one Area. Remember to program the zone for Keyswitch Arming in the Area to be disarmed.
...
View Answer
Answer:
Yes. Note that Quickloader only allows the conversion to a "larger" model control panel (i.e. you may convert a GEM-P816 control panel to a "larger" GEM-P1632, but cannot convert a GEM-P1632 to a "smaller" GEM-P816. At this time, a...
View Answer
Answer:
For the following control panels: GEM-P3200, GEM-P9600, GEM-X255 and all C-Series (GEMC):
...
View Answer
Answer:
The following is a description of SIA Central Station Report Codes for firmware versions 11D – 30 and versions 1B – 4:
...
View Answer
Answer:
If the Test Timer feature is programmed, an automatic test report will be transmitted to the central station on the scheduled day(s) at the scheduled time (UL installations require a report at least every 24 hours).
...
View Answer
Answer:
Yes. You can still use your old keypads and they will function normally, but you will not be able to access User Programming Mode nor Dealer Programming Mode.
View Answer
Answer:
When trying to arm the control panel, the appearance of a "Can't Arm, Incorrect Time" message may be due to one or more of the following settings:
...
View Answer
Answer:
Setup "Fail to Close" and "Fail to Open" with openings and closings as follows:
...
View Answer
Answer:
For control panels GEM-P3200, GEM-P9600, GEM-X255:
...
View Answer
Answer:
No, the GEM-TEMP64 is only compatible with the GEM-P816, GEM-P1632 and GEM-P1664 control panels, and only with firmware V30 and later.
View Answer
Answer:
Yes, you can use the firmware from a GEM-P3200 in a GEM-P9600 or GEM-X255 provided the same version firmware is used.
View Answer
40 Results Per Page | Showing
1-40 of 45 Results
| 1 |
2
