Results Per Page | Showing 1-16 of 16 Results
| 1
Answer:
Yes, you can map each GEM-KEYF button to a Gemini control panel using different point numbers for arming selected areas, or for sending panic alarms in those areas. For example, to program each button to arm different areas, designate a point for...
View Answer
Answer:
No, the GEM-TOUCH keypad does not support control panel programming. Only User Codes may be changed (requires a valid User Code that is configured for User Programming).
View Answer
Answer:
The only control panels that have integral Auto Disarm scheduling capabilities are the GEM-P3200, GEM-P9600 and GEM-X255 control panels, not the GEM-P1632, GEM-P816 and GEM-P1664 control panels.
...
View Answer
Answer:
The keypad communication bus on all NAPCO control panels is fully self-supervised and will locally annunciate a trouble if for any reason a programmed device does not respond to a control panel poll. Devices connected to the keypad communication bus,...
View Answer
Answer:
No, the GEM-K1VPS does not announce zone faults. However, the GEM-K1VPS will annunciate all keypad menu options, including:
...
View Answer
Answer:
Yes. The following is a helpful guide to basic NAPCO Gemini security system operations:
...
View Answer
Answer:
Yes, you can independently turn off the backlighting of the LCD display and/or the backlighting of the keypad buttons. The models GEM-K1CA and GEM-RP1CAe2 do NOT allow the adjustment of the backlighting intensity (dimness or brightness).
...
View Answer
Answer:
Yes, you can independently turn off the backlighting of the LCD display and/or the backlighting of the keypad buttons. The model GEM-K4RF keypad does NOT allow the adjustment of the backlighting intensity (dimness or brightness).
...
View Answer
Answer:
Yes, you can disable the GEM-K1VPS keypad LCD display backlighting on this keypad. You can also have this backlighting auto-dim, and then auto-increase when motion is detected by the integral PIR motion detector (see below for details). ...
View Answer
Answer:
Enter Program Mode using the keypad or using PCD-Windows Quickloader download software and remove the RF IDs of the wireless devices from the system. After the RF IDs are removed, you will then be able to remove the zones from the Area....
View Answer
Answer:
The System Sensor COSMOD2W and COSMOD4W interface modules are UL Listed for use with suitably rated UL Residential and Commercial Fire Alarm Control Panels. In addition, the COSMO-2W 2-wire module does not require a 2-wire compatibility listing...
View Answer
Answer:
With the Gemini control panel models GEM-P816, GEM-P1632, GEM-P1664, GEM-P3200, GEM-P9600 or GEM-X255 and the GEM-RP1 series or GEM-K1 series two-line LCD keypads:
...
View Answer
Answer:
At the keypad, first press RESET to acknowledge the trouble, then press FUNCTION or MENU (depending on the keypad model) repeatedly until Reset System Trouble Y/N appears, then press YES.
...
View Answer
Answer:
(This FAQ applies to all Gemini alarm control panels except the GEM-P400, GEM-P600, GEM-P800 and GEM-P801):
...
View Answer
Answer:
No, a Service Code will only disarm a system that has been armed with the Service Code. If the control panel was armed by any other means (e.g. Auto Arm, Easy Arm, a normal User Code), then the Service Code is not valid to disarm the...
View Answer
Answer:
Run PCD-Windows Quickloader software, open the Keypad Assignment screen, ACM Assignment tab. Check the "Enable Napco Proprietary Access Format" check box (or enable location 2780 and add "2"). In addition, ensure a schedule was not...
View Answer
40 Results Per Page | Showing 1-16 of 16 Results
| 1
