Answer:
If the Controller is set to Non-Polling mode under Channels/Comports, the TXD and RXD LEDs will not flash as frequently.
View Answer
Answer:
The three legacy panels (Microterm, Miniterm and Smarterm) do work with the CA4K software, but it is recommended to upgrade to a more modern panel. Many advanced features of CA4K are not supported on these three legacy panels, and you will find some...
View Answer
Answer:
No...It can be turned off in the Lantronix settings.
View Answer
Answer:
On the Accelaterm, there are two memory coin cells you must be concerned with. The first is on the Interface board and the second is on the processor board, that is located on the top of the unit. The coin cell battery on the interface board is...
View Answer
Answer:
The part number for the Memory Coin Cell in the Super Two is BR1225 (Panasonic, Energizer or Duracell). This battery can be purchased at most retail stores. Refer to the Super Two Service and Installation manual for replacement information...
View Answer
Answer:
The BAUD settings for each of the 3 jumpers are:
JUMPER BAUDA -RS485 1200B 2400C 38.4None 9600
D - RS232 1200E 2400F 38.4None 9600
View Answer
Answer:
One or two batteries can be used. For 4 hours of standby, two 12V -12AH batteries are required. The batteries should be placed in the bottom right of the cabinet.
...
View Answer
Answer:
The specifications for the CICP2100S surface mount controllers are almost identical as the CICP2100 controller.
...
View Answer
Answer:
The CICP2100S is the Surface Mount version of the Universe controller.
View Answer
Answer:
YES...Both the CICP2100 and CICP2100S controllers can be powered by a POE switch or midspan POE injector that can provide at least 12 Watts. The most common POE Injectors are rated at 15.5 watts.
...
View Answer
Answer:
YES...HSPD-12 is incorporated in the FIPS-201 specification. Continental controllers support FIPS-201.
View Answer
Answer:
If you are not using Door Contacts (Door Sensors), you must set the Door Sensor =0 under Configuration>Readers and then you MUST perform a DATA DOWNLOAD to the panel. This requirement was added into the Continental Software in 2017.
View Answer
Answer:
Yes, Virtual inputs are supported on Reader 1 of the CICP2100 and CICP2100 (uniVerse) controller. Virtual Inputs on Reader 2 are not supported since you cannot configure a door sensor or strike relay on Reader 2.
...
View Answer
Answer:
If all the Network settings are correct and the CA4K is programmed correctly, verify the following things:
...
View Answer
Answer:
Only 1 door is supported with a reader on each side of the door (in/out reader).
View Answer
Answer:
The CICP2100 and the CICP2100S is only supported on V2.11.84 of CA3000.
View Answer
Answer:
The CICP2100 and the CICP2100S uniVerse controllers defaults to DHCP mode. A DHCP enabled router/gateway is recommended to provide an initial IP address to the CICP2100 and the CICP2100S. Once a DHCP address is provided to the Universe unit, then you...
View Answer
Answer:
The accessory power (+5v and +12v) is available on the connector labeled "RDR PWR OUT". There is a total of 700ma max. available on the +12v output and 350mA max. on the +5v output.
View Answer
Answer:
These two boards almost look identical. There is one easy way of telling. There is a crystal on both boards. The crystal is labeled Y1. If the value of Y1 is 22.11MHz, then it would be a Turbo Superterm. If its 11.05MHz then it would be a...
View Answer
Answer:
When upgrading to CA4K, there are two chips on older Superterms that might need to be updated. Below are the two chips to be concerned with:
...
View Answer
Answer:
MOST COMMON ISSUE: Unlike other Continental Controllers, the Accelaterm (CICP2800) does not automatically initiate a firmware download when powered up for the first time. You MUST manually force a firmware download.
...
View Answer
Answer:
Yes, the grounds are common between the +5V accessory power Connector and the Reader Port Ground.
View Answer
Answer:
For both an 8 and 16 door Accelaterm, the first relay number on the Accelaterm I/O Expander unit is #17.
...
View Answer
Answer:
Inputs on a 4 Door Turbo Superterm and a 4 Door Superterm map identical to a Smarterm. Using the wrong input numbers is a very common error that users make. For instance, the auxialary inputs on the top left of the board are...
View Answer
Answer:
Refer to the Continental Controller Service Manuals.
...
View Answer
Answer:
On some panels, a charged battery will not power up a panel that was not previously connected to AC. It requires the panel be connected to AC and then lose the AC. At that point, the battery will kick in immediately.
View Answer
Answer:
The Accelaterm is shipped with a network interface board as a standard feature. It is recommended to use it.
...
View Answer
Answer:
YES...
Continental Access sells a supported USB to 9 pin serial adaptor. The part number for the converter is PCI-USB.
View Answer
Answer:
Badge Activity Links are not supported on Reader 16 of an Accelaterm.
View Answer
Answer:
Elevator Controls are not supported on Reader 16 of an Accelaterm.
View Answer
Answer:
1) Set the address switches to 99.
...
View Answer
Answer:
There are 4 firmware images in the CardAccess 3000 folder and CA4K folder. The files are smart.img, smart2.img, super2.img, cicp2100.img and accel.img.
...
View Answer
Answer:
WARNING: WHEN APPLYING EXTERNAL POWER INTO JP4, YOU MUST BE VERY CAREFUL WHILE CONFIGURING JUMPERS JP5 AND JP6. FAILURE TO DO SO WILL RESULT IN DAMAGE TO THE UNIT.
...
View Answer
Answer:
Note: An 8 door Accelaterm can have up to 3 I/O expansion boards connected to it. A 16 door Accelaterm can only have 2 I/O expansion boards connected to it. Each I/O expansion board contains 16 additional inputs and 16 additional...
View Answer
Answer:
Below is a list of Maximum baud rates for the Continental Controllers?
...
View Answer
Answer:
The T2 light is used to display the status of Auto-Baud. The T2 light will flash as the board is sequencing through different baud rates. When it locks on to a baud rate, the light can be on solid or completely off depending on the baud rate the...
View Answer
Answer:
Accelaterm = NO
Turbo Superterm = NO
Superterm = NO
Super Two = YES
The Super Two is the only controller where the inputs have a common ground.
View Answer
40 Results Per Page | Showing
1-40 of 45 Results
| 1 |
2
