Results Per Page | Showing 1-22 of 22 Results
| 1
Answer:
If you are experiencing slow AL-DTM Data Transfer Module speeds when communicating, it is likely that the wrong driver is installed, causing delays and sometimes termination of the communication link. The following steps provide a solution:
...
View Answer
Answer:
Door Select Mode is used to transfer programming and assign LockID numbers from DL-Windows (see OI382 for more information and full instructions).
...
View Answer
Answer:
The lock ring that secures our cylinder to the PG21 utilizes National Fine (UNF) threading as opposed to National Coarse (UNC) threading. The finer UNF threading allows for better load-carrying ability. Finer pitch threads are used mostly in...
View Answer
Answer:
Andy Phelps, Alarm Lock's National Training manager, shows you how to program a Trilogy lock using the AL-DTM-III. This session is for a newly installed lock, in default mode.
View Answer
Answer:
Andy Phelps, Alarm Lock's National Training manager, shows you how to program a Trilogy lock using the AL-DTM (Data Transfer Module).
View Answer
Answer:
This instructional video shows how to assemble the Alarm Lock Exit Trim Cylinder Adapter Kit. This kit is used when changing the factory cylinder to a different cylinder (such as the Best Small Format IC or a Large Format Removable Core).
View Answer
Answer:
See images below. Mounting the external door pull for Models 250 / 260, 700 / 710 and 715 is relatively simple. Packed inside the Model 707 Door Pull box is a mounting template (P3191). Use this template for drilling the correct...
View Answer
Answer:
The infrared (IR) receiver on the RR-PM1200 may be altered by fluorescent light fixtures (fixtures of the type often used in office buildings). The light coming from fluorescent fixtures can mix with the light signal from the AL-REMOTE keyfob...
View Answer
Answer:
The special shaped cam supplied with all narrow stile models is not engineered to be transferable to unlike cylinders. To accommodate this situation, Alarm Lock manufactures a selection of cams designed to fit popular cylinder brands. ...
View Answer
Answer:
Wire the RR-RECEIVER to the locking device you wish to control using as required. Perform the following steps precisely:
...
View Answer
Answer:
The part number for the battery pack used with the Networx DL6100 and PDL6100 door locks is S6181.
View Answer
Answer:
When adding a new locking device to your existing system using an AL-DTM-III, be sure the AL-DTM-III is in "Door Select Mode" to allow communication. To access "Door Select Mode", simply "default" (restore the AL-DTM-III to its original factory...
View Answer
Answer:
Ensure your AL-DTM III is set to the correct mode to be compatible with your DL-Windows software version. Basically, DL-Windows version 3.0.4 (and earlier) will require your AL-DTM III to be configured to AL-DTM II ("2") mode. DL-Windows...
View Answer
Answer:
1 Configure the AL-DTM III for Door Select Mode:
...
View Answer
Answer:
Any one of the three drivers will work with your Alarm Lock AL-PCI2 cable and MX1130 cable. However, to ensure you have the latest version driver, we recommend you search the Napco Technical Library website (tech.napcosecurity.com) with the...
View Answer
Answer:
This display is normal. To be backward compatible with older locking devices and older software versions, the AL-DTM-III has within its firmware the instructions to request the 299 code a second time. This request is normal. With...
View Answer
Answer:
No, Sebury proximity cards are not yet able to be read by any Alarm Lock product.
View Answer
Answer:
This optional outside pull handle measures 8-5/8" (height) by 1-5/8" (width). See Image below:
View Answer
Answer:
For Models DL2700, DL2800, DL3000, PDL3000, DL3200, DL4100, PDL4100, DL6100, PDL6100 when configured for Yale full-format interchangeable core:
...
View Answer
Answer:
As long as there is a gap of 3/16" or more between the edge of the door and the door jamb, you can use Alarm Lock part CW-27S (stainless steel wrap-around plate shown below) to cover damage, wrong holes, or convert a mortise lock door prep to a...
View Answer
Answer:
Cylinders made by Schlage for their A Series locksets will fit into Alarm Lock lever sets. Remember; you must use the proprietary tailpiece made by Alarm Lock (Alarm Lock tailpiece part number HW580).
View Answer
Answer:
Only Sargent "6-Line" cylinders will fit into Alarm Lock lever-sets.Remember: You must use the proprietary tailpiece made by Alarm Lock.The original tailpiece supplied with the Alarm Lock cylinder will snap directly into the Sargent...
View Answer
40 Results Per Page | Showing 1-22 of 22 Results
| 1
