Results Per Page | Showing 1-32 of 32 Results
| 1
Answer:
Access the Prima dealer portal website, go to System > Gateway Status, and reference the Hardware Type. The example system shown below is connected by cellular (the Hardware Type is "LTE").
...
View Answer
Answer:
The NAPCO Prima dealer portal website (www.NapcoPrima.Pro) allows you to add new (and delete existing) Prima Super Panels (called "gateways" in the website).
...
View Answer
Answer:
The StarLink Connect radios are capable of dual path reporting, from the installation site to the NAPCO NOC (www.NapcoNOC.com) over the Internet, with cellar backup. Note: Wi-Fi cannot be used on UL Burglary installations.
...
View Answer
Answer:
Wire a network cable from the radio Ethernet port to the customer's router / network.
...
View Answer
Answer:
Wire a network cable from the radio Ethernet port to the customer's router / network.
...
View Answer
Answer:
Wire a network cable from the radio Ethernet port to the customer's router / network.
...
View Answer
Answer:
Wire a network cable from the radio Ethernet port to the customer's router / network.
...
View Answer
Answer:
Wire a network cable from the radio Ethernet port to the customer's router / network.
...
View Answer
Answer:
Wire a network cable from the radio Ethernet port to the customer's router / network.
...
View Answer
Answer:
Source IP address changes are rare; the outgoing load dictates the need to route the packets through a different gateway in real-time. When this does happen, the Sur-Gard receiver sees a different source IP address for certain reports (compared...
View Answer
Answer:
Source IP address changes are rare; the outgoing load dictates the need to route the packets through a different gateway in real-time. When this does happen, the Sur-Gard receiver sees a different source IP address for certain reports (compared...
View Answer
Answer:
Source IP address changes are rare; the outgoing load dictates the need to route the packets through a different gateway in real-time. When this does happen, the Sur-Gard receiver sees a different source IP address for certain reports (compared...
View Answer
Answer:
Yes. In the NAPCO NOC (www.napconoc2.com), click Communication and/or the IP tab. Set the IP Configuration Type pull-down to Static.
...
View Answer
Answer:
Yes. In the NAPCO NOC (www.napconoc2.com), click Communication and/or the IP tab. Set the IP Configuration Type pull-down to Static.
...
View Answer
Answer:
Yes. In the NAPCO NOC (www.napconoc2.com), click Communication and/or the IP tab. Set the IP Configuration Type pull-down to Static.
Note: You must enter the IP Address, Subnet Mask and Default Gateway of the network.
View Answer
Answer:
Dual Path to NOC, with NOC IP communication backed up by dial-up to CS receiver.
...
View Answer
Answer:
Dual Path to NOC with NOC dial-up communication to CS receiver.
...
View Answer
Answer:
The IBR-ZREMOTE has been tested and approved for use with a Verizon FiOS model G1100 Router / Gateway with the settings shown below. Note: If your Router / Gateway firmware versions do not exactly match the versions that appear in the...
View Answer
Answer:
Simply connect your analog cameras to our iSeeVideo Single Channel Gateway (part # ISEE-SCHGW), converting the analog signal to digital IP, allowing the IBR-ITAB tablets and the iBridge app to display video.
View Answer
Answer:
No, the WAP does not need to be registered. Only the iSeeVideo cameras, the ISEE-SCHGW Video Gateways and ISEE-IVR Internet Video Recorders need to be registered on the ComNet Site.
View Answer
Answer:
If using wireless cameras, a Live Monitor Output is not supported. However, you can use an ISEE-SCHGW Single Channel Video Gateway or the new 4-Channel Gateway (available soon). These gateway modules have a Monitor Output BNC socket that...
View Answer
Answer:
In addition to its outstanding abilities as a high-resolution outdoor wireless camera, the Napco ISV WLOCAM infrared IP camera has features that allow the use of its integral PIR motion sensor and pixel-based analytics to be used as a wireless...
View Answer
Answer:
Third party IP cameras cannot be used on the iSeeVideo server, however analog cameras can always be used on the iSeeVideo server when coupled with a single channel gateway. In addition, single channel gateways also have a loop output to feed...
View Answer
Answer:
While the VCAM-I and VIP-Gateway are assigned static IP addresses, they can operate on a DHCP network. In addition to its IP address, each device must also be assigned an alphanumeric name to make it easy for the user to remember and find. Every 16...
View Answer
Answer:
No – the VIP-Gateway converts up to 4 analog cameras into Network IP cameras and the VCAM-I is an IP ready camera. The VCAM-I cannot be interfaced to the VIP-Gateway. If multiple IP cameras are needed on a site, it would be more cost effective...
View Answer
Answer:
The camera and the VIP-Gateway both have built-in motion detection capability, with sensitivity adjustments and a time schedule. They can be armed by schedule to trigger an event upon motion detection.
View Answer
Answer:
The NAPCO VCAM-I IP and VIP-Gateway transmit to the server approx. 12 seconds of pre-alarm (before trigger) and 18 seconds of post-alarm video for a total of 30 seconds.
View Answer
Answer:
The VCAM-I AP application is for configuring the VIP-Gateway and VCAM-I devices during installation and maintaining the settings remotely. It should not be left with the customer. While the VCAM-I AP can technically be used as a viewer for the...
View Answer
Answer:
A short occurs on the n/o trigger input of the device (VIP-Gateway or VCAM-I).
...
View Answer
Answer:
The NAPCO VIP-Gateway and VCAM-I IP both send compressed video clips to the NAPCO Video Alert server upon activation of the module’s trigger input(s). This trigger activation is accomplished by placing a momentary short across a normally open...
View Answer
Answer:
The NAPCO Video Alert Server (http://www.videoalert.net/) stores digital video clips transmitted from the NAPCO ISVWLCAM, ISVWLCAM, ISVWLOCAM, ISVWLHDCAM, ISV-WLOHD wireless-based cameras, the ISEE-SCHGW single camera IP Gateway module or video...
View Answer
40 Results Per Page | Showing 1-32 of 32 Results
| 1
