Results Per Page | Showing 1-25 of 25 Results
| 1
Answer:
First In Area (Free Access Lockdown) prevents doors from entering Free Access status until a first-in card swipe or pin entry. Note: This feature is similar Enable Passage by Group in DL-Windows.
...
View Answer
Answer:
MVP Access uses the following outbound ports for secure communication:
...
View Answer
Answer:
When updating the Network Board's firmware to the MVP cloud version, in uniVerse Finder, if the user changes the Operation Mode to "Mode A" before attempting the firmware update, the update will not proceed. The Operator must switch the mode back to...
View Answer
Answer:
V1.5.0.8 or later supports CICP1300NETBD2 (For CICP1300), CICP2800NETBD2 (For CICP2800), CICP2100/CICP2100S, CA-1, CA-2
...
View Answer
Answer:
Important: Only GEN3 Gateways are eligible for conversion to MVP Access. The uniVerse Finder Utility Software must be installed on the same local area network as the gateway.
...
View Answer
Answer:
With the GEM-P3200, GEM-P9600, GEM-X255 or Gemini C-Series (GEMC) control panels, the IBR-ZREMOTE must be connected to the control panel bus. In the PCD-Windows Quickloader Keypad Assignment screen, Keypad Assignment tab (shown below), select RCM for...
View Answer
Answer:
With NAPCO control panels, the IBR-ZREMOTE must be connected to a Gemini GEM-P3200, GEM-P9600, GEM-X255 or Gemini C-Series (GEMC) control panel. The IBR-ZREMOTE must be connected to the control panel bus and programmed as a keypad with its Type as an...
View Answer
Answer:
1) There is a button in Camera configuration page to Synchronize PC time to DVR Servers.
2) Also, can use CICTimeSync.exe file in tools folder to Synchronize PC time with Global Time synch servers, like in CA3000
View Answer
Answer:
Yes, the NAPCO IBR-ZREMOTE Z-Wave Controller can integrate with a Savant Home Automation system, allowing a Savant system to take full advantage of NAPCO's security system and all of its associated features. Below is a list of required firmware,...
View Answer
Answer:
Until the release of CardAccess 3000 V2.9.88, the only communications option for the Napco Integration was the utilization of an NL-MOD. The NL-MOD provided communications between the CardAccess 3000 software and the Napco...
View Answer
Answer:
The username(s) must be set up on the Salient Client that match the username(s) on the Salient Server.
View Answer
Answer:
Prior to configuring the CardAccess 3000 or CA4K Napco Integration, it is highly recommended to contact the Napco Technical Support group first. You must verify you have a fully programmed and functional Napco Alarm Panel that is communicating...
View Answer
Answer:
When using Salient DVR's with the CardAccess 3000, camera one must be live at all times. If camera 1 loses it's signal or is not configured, an error will display.
View Answer
Answer:
1) Under "Configuration>DVR Configuration", you must specifiy the port number after the "DVR Server IP".
...
View Answer
Answer:
In the Salient Software, you must configure a Motion Zone for the camera.
View Answer
Answer:
Yes...
The Napco Integration feature must be purchased and enabled in the CardAccess 3000 security key/software license.
View Answer
Answer:
You must verify the security key /soft license supports one or more DVR's. This is a feature that must be purchased.
...
View Answer
Answer:
CardAccess 3000 V2.9.x integrate with the following DVR's:
...
View Answer
Answer:
Forced Recording is when an action such as a Card Swipe at a specific reader, forces recording to start on the DVR for a certain amount of time.
...
View Answer
Answer:
DVR Notification is a feature that notifies the CardAccess 3000 when motion is detected on a particular camera.
...
View Answer
Answer:
CA4K support all the models listed below.
...
View Answer
Answer:
Launch the CardAccess License manager to view the settings in the security key/software license. The CardAccess license manager can be found under Start>All Programs>CardAccess 3000.
...
View Answer
40 Results Per Page | Showing 1-25 of 25 Results
| 1
