Results Per Page | Showing 1-29 of 29 Results
| 1
Answer:
For the GEMC Fire Side of the GEMC Control Panel:
...
View Answer
Answer:
Yes! You can use dial capture technology (capturing alarms from the DACT connections to communicator Telco Primary and Secondary Jacks 1 & 2) and also capture alarms through the 4 supervised communicator inputs at the same time.
...
View Answer
Answer:
No. Network reporting is not required to program an IP receiver. In addition, network reporting only exists between the communicator and the NOC (before the report is transferred to the central station).
View Answer
Answer:
Yes, by removing the JP2 shunt and enabling the feature "Tip/Ring Wiring Fault Report", when any communicator trouble is detected, the StarLink communicator will remove voltage from the secondary telephone output, triggering the FACP to locally...
View Answer
Answer:
Yes. To have a StarLink Fire communicator report an IP Test Timer, log into the NAPCO NOC website (www.NapcoNOC.com), enter the Primary IP address and a backup IP (or telephone number), then select Save. After saving, the CS Test Timer tab will...
View Answer
Answer:
The LTE dual path communicators come with four supervised inputs that can be wired to a FACP without a DACT to provide four signals without the need for the 9SLE10KHARN Wire Harness.
...
View Answer
Answer:
The LTE dual path communicators come with four supervised inputs that can be wired to a FACP without a DACT to provide four signals without the need for the 9SLE10KHARN Wire Harness.
...
View Answer
Answer:
Dual Path Reporting: A dual path communicator is connected to the network at the protected premises through its integral Ethernet port, or Wi-Fi using the optional SLE-WIFI MODULE. The primary communications are typically through the Internet, with...
View Answer
Answer:
The new StarLink Fire dual path communicator models include the following features:
...
View Answer
Answer:
Yes. In the StarLink SLE Management website (www.NapcoNOC.com), enter Dealer Programming and add both the primary and secondary telephone numbers of the two receivers. Optionally, enter duplicate primary and duplicate secondary telephone numbers of...
View Answer
Answer:
To redirect the alarm communications of a control panel with an unknown Dealer or Master Security Code using a StarLink communicator, proceed as follows:
...
View Answer
Answer:
Observe the D607 green LED located at the center-right end of the radio PC board. The number of blinks indicates the control panel to which the StarLink Connect radio is set.
...
View Answer
Answer:
When using the www.NapcoNOC.com website to program the StarLink radio with the central station telephone number, a convenient new clipboard feature allows the telephone number to be automatically copied to the Advanced tab. To use this new...
View Answer
Answer:
The wiring diagram illustrates the connections to a Gemini GEMC Commercial Fire control panel with an SLE-CDMA-FIRE radio mounted remotely (up to 100 feet away). Also shown are the SLE-DLEXT Download Extender Module connections necessary...
View Answer
Answer:
Dual Path to NOC with NOC dial-up communication to CS receiver.
...
View Answer
Answer:
The number of blinks the green LED marked D607 (located at the center right side of the radio PCB) indicates the control panel set in the StarLink Connect radio:
...
View Answer
Answer:
No, the radio must be powered with 12 volts from the GEMC control panel to allow uploading and downloading.
View Answer
Answer:
The StarLink radio can be configured to report redundantly, where all events will be reported by both the alarm control panel DACT and the radio. Proceed as follows:
...
View Answer
Answer:
Used when the SLE-GSM radio is mounted more than 6 feet from the control panel, the SLE-DLEXT is connected between the control panel and the SLE-GSM and provides the means to remotely communicate (download/upload program and status) through the...
View Answer
Answer:
Used when the SLE-GSM radio is mounted more than 6 feet from the control panel, the SLE-DLEXT is connected between the control panel and the SLE-GSM and provides the means to remotely communicate (download/upload program and status) through the...
View Answer
Answer:
To use the "NAPCO Control Panel Serial Port" when using the StarLink SLE-GSM / CDMA radios, the following minimum control panel firmware versions are required:
...
View Answer
Answer:
Yes, IP reporting from the NOC to any Central Station equipped with a Sur-Gard receiver is supported. This IP reporting feature may be used with all NAPCO StarLink SLE-GSM, SLE-GSM-3/4G and SLE-CDMA radios, regardless of the firmware version....
View Answer
Answer:
Yes, the NAPCO StarLink NOC supports arming and disarming through the same cable used for downloading (SLE-DLCBL download cable). Connecting a StarLink radio to a Gemini control panel serial port means there is no longer a need to program and...
View Answer
Answer:
If using the SLE Alarm Communicator as a primary communicator, 8 wires are required. If using the SLE Alarm Communicator as a backup, 10 wires are required. The recommended minimum (thinnest) wire gauge is 22AWG. We recommend...
View Answer
Answer:
No, the control panel can only send signals either through the SLe-GSM only (Primary Mode), or over telephone lines with the SLe-GSM programmed as a backup, taking over if the telephone line is cut (Backup Mode).
...
View Answer
Answer:
The StarLink SLe-GSM and SLe-GSM-3/4G radios are fully compatible with ALL Gemini control panel versions. The SLe-GSM-8D-3/4G adds compatibility with the Gemini GEM-P400, GEM-P800, GEM-P801, Express XP-400 and XP-800 series control...
View Answer
Answer:
NOTE: This Applies to the Following Products:
...
View Answer
Answer:
Yes. The SLe-GSM can be used to download GEM-P3200 and GEM-P9600 control panels running firmware version 11C or greater, which was released in May of 1999. It can also download to GEM-P816, GEM-P1632 and GEM-P1664 controls running...
View Answer
Answer:
There are two terminals marked TIP and RING on the SLe-GSM terminal strip: One pair is marked PANEL TIP and PANEL RING (with 27V) and one pair is marked TIP and RING (with 0 volts). Ensure the control panel is connected to the radio Primary...
View Answer
40 Results Per Page | Showing 1-29 of 29 Results
| 1
