Results Per Page | Showing 1-26 of 26 Results
| 1
Date Added: 10/5/04
Installation Instructions for FW-4, FW4-H, FW-2 and the FW2-H
Posted in [Installation Manuals]
Tags:
Date Added: 10/23/99
Firewolf Control Panel Installation Instructions FW-C2Z, FW-C4Z, FW-C4EZ.
Posted in [Installation Manuals]
Tags:
Date Added: 11/12/04
Firewolf FW-4, FW4-H, FW-2 and the FW2-H Smoke Detector Installation Instructions
Posted in [Installation Manuals]
Tags:
Date Added: 6/11/01
Firewolf FW-2 Smoke Detector Product Advisory
Posted in [Tech Notes]
Tags:
Date Added: 10/23/99
Addendum to the "Testing The FW-4 and the FW-2 Installation" section of the FW-4 and FW-2 Installation Instructions (WI972).
Posted in [Installation Manuals]
Tags:
Date Added: 4/27/10
Firewolf FW-2S Smoke Detector with integral sounder, FW-2SHEAD and FW-2SBASE Installation Instructions
Posted in [Installation Manuals]
Tags:
Date Added: 4/1/13
Data Sheet: Conventional Smoke Detection Models FW-2, FW2-H, FW-4, FW4-H (A638).
Posted in [Data Sheets - AHJ Submittal]
Tags:
Date Added: 4/1/13
Data Sheet: Addressable Contact Monitoring Modules FWC-FSLC-EZM1, FWC-FSLC-EZM2 (A626).
Posted in [Data Sheets - AHJ Submittal]
Tags:
Date Added: 12/3/15
This Tech Tip describes the various Fire SLC Signaling Line Circuit modules, their functions and typical applications.
Posted in [Tech Tips]
Tags:
Date Added: 3/10/16
How to generate an AHJ (Authority Having Jurisdiction) Report for FWC-FSLC detectors.
Models: Gemini C-Series (GEMC) / Firewolf
Posted in [Tech Tips]
Tags:
Date Added: 3/17/16
How to program the Test Timer feature (GEMC Control Panels).
Posted in [Tech Tips]
Tags:
Date Added: 6/24/16
How to enable cadence for older fire horns.
When retrofitting older GEMC / Firewolf control panels, installers may find older horns and/or 4-wire horn strobes installed. Unlike the newer smart devices, these older NAC devices may not include a pre-programmed Temporal 3 cadence. This Tech Tip describes how these older NAC devices can be wired to the control panel in order to have the control panel generate the Temporal 3 cadence.
Posted in [Tech Tips]
Tags:
Date Added: 7/12/16
This Tech Tip details the basic standard programming, configuration and installation requirements of a coded fire alarm system.
Posted in [Tech Tips]
Tags:
Date Added: 2/21/18
Wiring 2-Wire Smoke Detectors to the Napco Firewolf FW-RM1 Reversing Module.
Posted in [Tech Tips]
Tags:
Date Added: 3/18/20
Data Sheet: Addressable Manual Fire Pull Stations FWCâ€FSLCâ€PULL, FWCâ€FSLCâ€PULLK, FWCâ€FSLCâ€PULL2K, FWCâ€FSLCâ€PULL2 (A629).
Posted in [Data Sheets - AHJ Submittal]
Tags:
Date Added: 7/21/22
Ever since the NFPA 72 (2013) was instituted, a 6-hour Test Timer may be required to be programmed in your Gemini C-Series (GEMC), Firewolf or FireLink control panel. See this Tech Tip for programming instructions.
Posted in [Tech Tips]
Tags:
Date Added: 3/24/23
FWC-FSLC-RM2-E Dual Relay Module Quick Reference Guide (WI2459)
The Dual Relay Module (FWC-FSLC-RM2-E) is to be connected to NAPCO DCP Signaling Line Circuit (SLC). The FWC-FSLC-RM2-E provides two separately controlled sets of Form-C dry relay contacts for general purpose control functions at one address point. Typical applications are where normally open or normally closed contacts are needed. Examples include elevator recall, door closure, turning fans on or off, and auxiliary indications.
Posted in [Quick Start Guides]
Tags:
Date Added: 3/24/23
FWC-FSLC-SOM1-E Supervised Output Module Quick Reference Guide (WI2460)
The Supervised Output Module (FWC-FSLC-SOM1-E) is to be connected to NAPCO DCP Signaling Line Circuit (SLC). Typical applications are supervised 24VDC to output to audible and visual fire alarm indicating devices such as horns, bells, strobes, etc. Indicating device output provides supervision for open and short circuit conditions. Uses auxiliary power input for device operation and for powering signaling devices.
Posted in [Quick Start Guides]
Tags: