Date Added: 2/13/17
NETPDK / NETDK Networx Panel Programming Instructions.
IMPORTANT: After completing the NETWORXPANEL and DK keypad firmware upgrade, we strongly recommend that you reset, re-discover and re-download the NETWORXPANEL program to ensure the proper and reliable performance of the unit. See Function 99, "Clear All Lock Programming" (WI1855 page 28) for more information.
Posted in [Programming Manuals]
Tags:
Date Added: 2/17/17
NETWORXPANEL Firmware V64t and NETPDK / NETDK Keypad Firmware V65.e
The NETWORXPANEL (upgraded to V64t) and the keypad(s) (upgraded to V65.e) must BOTH be upgraded using the following steps:
1. Download the two firmware .bin files to your computer.
2. Open DL-Windows and right-click the "Netpanel" Lock Profile.
3. Select Update Lock Firmware from the pop-up menu.
4. In the Open screen, navigate to the folder on your computer containing the downloaded .bin files.
5. Select the file named "DKControl_64t.bin" and click Open. The firmware will begin to install.
6. Confirm the new "Netpanel" version number located on the Lock Status screen.
7. Repeat steps 2 through 6 but select the file "DKNKeypad_65e.bin".
8. Confirm the keypad firmware by power cycling the NETWORXPANEL. Within 10 minutes of cycling power, press and hold the number 1 key. Verify that the red LED flashes "1 short blink" (indicates version e).
Note: If two keypads are being upgraded, and they are both wired to the NETWORXPANEL, both keypads will be upgraded consecutively; you do not need to install the second .bin file twice.
IMPORTANT! After performing the above upgrade procedure, you MUST perform a FULL reset using the "ERASE ALL PROGRAMMING" procedure described in the NETWORXPANEL programming instructions (WI1856).
Note: The firmware version letter type case ("upper case" or "lower case") displayed in the file name may differ and from the case displayed in DL-Windows. Be aware that both types of letters always denote the same version.
FIRMWARE UPDATE 64T INCLUDES THE FOLLOWING NEW FEATURES:
- Supports advanced Two-Door Mode setup (see WI1855 for full details)
- Lock responds to GLOBAL Emergency Lockdown commands
- Lock responds to LOCAL Emergency Lockdown commands
- Faster communication "Wake up" time when using version 2 Gateways
Support added for the following keypad programming options:
(AL) 8 Exit Program Mode
(AL) 67 (AL) 43 Enable Sounder on Emergency
(AL) 67 (AL) 45 Activate Local Emergency (by keypad)
(AL) 67 (AL) 46 Activate Global Emergency (by keypad)
(AL) 67 (AL) 47 Activate Local Emergency (by keyfob; requires RR-4BKEYFOB)
(AL) 67 (AL) 48 Activate Global Emergency (by keyfob; requires RR-4BKEYFOB)
Posted in [Software / Firmware]
Tags:
Date Added: 2/22/13
File name: DKNKeyPad_65a.bin
NETPDK / NETDK Firmware - 65a.
To Install: Unzip the .bin file to your C:\DL-Windows\Firmware directory. Right-click the desired NETWORXPANEL in the DL-Windows left pane and select Update Lock Firmware. Browse for the new .bin file and click OK. When finished, the confirmation screen shows the NETWORXPANEL version only (NOT the keypad version). To verify the keypad firmware: Within 10 minutes of the previously described update process, press and hold the "1" key on the keypad for 10 seconds and listen for a short beep followed by a long beep. Note: This file will update the firmware that exists within the keypad, not the NETWORXPANEL.
Note: The firmware version letter type case ("upper case" or "lower case") displayed in the file name may differ and from the case displayed in DL-Windows. Be aware that both letters always denote the same version.
Posted in [Software / Firmware]
Tags:
